Maré Set: Bandana + Beanie

09/08/2025

Level of difficulty

Size: 1 size

Materials:

1 skein Encanto Slim, color: 2307 (Maré)

Crochet hook: 3.0 mm

Scissors

Yarn needle

Sewing needle and thread

216 pearls, 4 mm

Liquid silicone glue

Tape measure

Stitch glossary and abbreviations:

Chain Stitch (ch.)

Single Crochet (sc.)

Double Crochet (dc.)

Execution

Beanie Instructions

Crown (closed part)

Round 1: Begin with a magic ring, ch 3 (counts as 1 dc), and make 11 dc into the ring. You will have 12 dc total (including the initial ch-3). Join with sl st to top of ch-3.

Round 2: Ch 3, dc in same st. Work 2 dc in each st around. Join with sl st to top of ch-3. (24 dc)

Round 3: Ch 3. 2 dc in next st, 1 dc in next st. Repeat around. Join with sl st.

Round 4: Ch 3. 1 dc in each of next 2 sts, 2 dc in next st. Repeat around. Join with sl st.

Round 5: Ch 3. 1 dc in each of next 3 sts, 2 dc in next st. Repeat around. Join with sl st.

Round 6: Ch 3. 1 dc in each of next 4 sts, 2 dc in next st. Repeat around. Join with sl st.

At this point the circle should measure about 11 cm across (adjust according to your tension).

Openwork Section (mesh)

Round 7: Ch 5, skip 2 sts, sc in next st; ch 5, skip 2 sts, sc in next st. Repeat around. At end: ch 2, dc into base of initial ch-3.

Note: all mesh rounds are ended this way.

Round 8 and onwards: Ch 5, sc in next loop, ch 5, sc in next loop. Repeat across.

Continue until you have 13 rounds of mesh (or adjust for desired length).

Edging Round

In first loop: sc, ch 1.

In next loop: (3 dc, ch 2, 3 dc, ch 1), then sc in next loop.

Repeat this pattern around: (sc, ch 1, (3 dc, ch 2, 3 dc, ch 1) in next loop, sc in next loop).

Finish round, join with sl st in first sc, fasten off.

Finishing the Beanie

●     After weaving in ends, apply a drop of liquid silicone glue to each end to prevent slipping (important with Encanto yarn).

●     For decorative detail, make pearl straps:

Thread 18 pearls on each strap using a sewing needle.

Sew from edge to edge across the beanie opening, forming pearl straps.

Bandana Instructions

Row 1 – foundation blocks

Make a magic ring.

Inside the ring: ch 4 (counts as 1 dc + ch-1), 3 dc, ch 2, 3 dc, ch 1, 1 dc.

This forms the initial triangle. 

Row 2 – base loops

Turn, ch 3 (counts as 1 dc + ch-1).

In the first space: 1 sc.

Ch 3.

In the center: 1 sc, ch 3, 1 sc.Continue with ch 3.

In the last space: 1 sc, ch 1, 1 dc.

Row 3 – blocks of 3 dc

Turn, ch 4 (counts as 1 dc + ch-1).In the first loop: 2 dc, ch 1.

In the following loops: 3 dc, ch 1 up to the center.

In the center (corner): 2 dc, ch 2, 2 dc.

Continue: ch 1, 3 dc, ch 1 across the loops.

In the last space: 2 dc, ch 1, 1 dc.

Row 4 – loops

Turn, ch 4 (counts as 1 dc + ch-1).In the first space: 1 sc.

Ch 3, 1 sc in each space until the center.

In the center: 1 sc, ch 3, 1 sc.Continue across with ch 3, 1 sc in each space.

In the last space: 1 sc, ch 1, 1 dc.

Repeat

Repeat Rows 3 and 4 alternately until reaching the desired size.

Example: 23 cm tall × 45 cm wide.

Side ties

At the end, ch 60 on one side and work sl st back across.

Along the bandana’s side edge, work: 3 sc in one space, 1 sc in the next space, repeating until the other side.

Then ch 60 again and work sl st back across.

Fringe

Cut yarn strands 10 cm long (folded in half = 5 cm).

Attach fringes evenly along both sides of the bandana.

Finishing

After weaving in ends, apply a drop of liquid silicone glue to each end to prevent them from slipping.

Maré Set.

Download • 962KB

Created by: Joana Gouveia, @FiosCruzados

 Disclaimer: measurements are approximate due to differences between centimeters and inches, needle sizes and tension. All care has been taken to allow accurate completion of the pattern.

See more about...